← Back to home

Tyre and wheel calculator

Compare your current and new setup. Calculate changes in diameter, ground clearance, speed and wheel position relative to the arch and suspension.

Current size

The sizes currently fitted to your vehicle.

WidthTyre width in millimetres. In 205/55 R16, this is 205.
Aspect ratioSidewall height as a percentage of tyre width. A value of 55 means 55% of the width.
DiameterWheel diameter in inches. R describes radial tyre construction, not radius.
Width, JRim width in inches. J describes the rim flange profile.
Offset, ETDistance between the wheel centreline and mounting face. A lower ET usually moves the wheel outwards.
BoltsNumber of bolt holes or studs. This must match on the current and new wheels.
PCD, mmDiameter of the circle through the bolt hole centres. In 5×114.3, 114.3 is the PCD; it must match exactly.
Hub, DIAHub spigot diameter in millimetres. The new wheel centre bore is compared with this.
New size

The sizes of the set you want to fit.

WidthNew tyre width in millimetres. An excessively wide tyre may rub the wheel arch or suspension.
Aspect ratioSidewall height as a percentage of the new tyre width. Together with width and rim diameter, it determines overall diameter.
DiameterNew wheel diameter in inches. It must match the tyre rim diameter.
Width, JNew rim width in inches. It affects sidewall position and the permissible tyre width.
Offset, ETNew wheel offset in millimetres. Changing it moves the wheel relative to the arch and suspension.
BoltsNumber of bolt holes on the new wheel. It must match the original exactly.
PCD, mmThe new wheel bolt pattern. Even a small difference in PCD is not acceptable.
Bore, DIANew wheel centre bore diameter. It may be larger than the hub with a suitable centring ring, but not smaller.

The basic dimensions are compatible

The bolt pattern matches, but the centre bore requires hub-centric rings.

Current

205/55 R16 · 6.5J ET45

New

225/45 R17 · 7.5J ET42

Speedometer reading

100.4 km/h

Actual speed when the speedometer reads 100 km/h

Ground clearance change

+1.2 mm

The vehicle will sit higher

Outer wheel position

+15.7 mm

The new wheel extends further out

Inner clearance

-9.7 mm

There will be less clearance to the suspension

Size comparison

ParameterCurrentNewDifference
Overall diameter631.9 mm634.3 mm+0.4%
Sidewall height112.8 mm101.3 mm-11.5 mm
Revolutions per km504502-2
The calculator compares geometry, PCD and centre bore. Check permitted tyre widths, load ratings, brake clearance, arch shape and manufacturer guidance for your specific vehicle.

How to read tyre markings

In 205/55 R16, 205 is the tyre width in millimetres, 55 is sidewall height as a percentage of width, and 16 is the rim diameter in inches.

Understanding wheel dimensions

For example, 7.5J ET42 5×114.3 DIA67.1 describes width, offset, bolt pattern and centre bore. PCD must match exactly, and the new wheel centre bore cannot be smaller than the hub.

Frequently asked questions

What tyre diameter difference is acceptable?

A difference within 2% of the original diameter is usually preferred. Check differences between 2% and 3% against your vehicle manual. The calculator flags differences above 3% as undesirable.

What do ET and wheel position mean?

ET is the distance between the wheel centreline and mounting face. Width and ET together determine how far a wheel moves towards the suspension or out towards the wheel arch.

Can I fit a wheel with a larger centre bore?

Yes, if the bolt pattern matches and appropriate hub-centric rings are used. A bore smaller than the hub will not fit without machining.

Does the calculator guarantee there will be no rubbing?

No. It compares basic geometry but does not know the brake, suspension or wheel arch shapes of your specific vehicle. Check the documentation and test-fit the wheels.